User Tools

Site Tools


extended_g-code_table

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
extended_g-code_table [2017/02/22 09:30]
Matthew Upp [M564 - Download file from remote server]
extended_g-code_table [2018/12/22 04:16] (current)
Matthew Upp
Line 1: Line 1:
 ~~NOTOC~~ ~~NOTOC~~
-====== ​Extended ​G-code Table ======+====== ​Custom ​G-code ​Commands ​Table ======
 <wrap lo>//​Standard Marlin compatible G-codes can be found at the [[http://​reprap.org/​wiki/​G-code|RepRap wiki: G-code]]. \\ <wrap lo>//​Standard Marlin compatible G-codes can be found at the [[http://​reprap.org/​wiki/​G-code|RepRap wiki: G-code]]. \\
-Not all standard G-code are supported by the MP Select Mini.//</​wrap>​+Not all standard G-code are supported by the MP Select Mini.//</​wrap> ​\\
 See [[g-code#​sending_g-code|Sending G-code]] for more information on how to send the commands below. See [[g-code#​sending_g-code|Sending G-code]] for more information on how to send the commands below.
  
-^ Command ​                                                                  ​^ Description ​                                      ​+ 
-| [[extended_g-code_table#​m550_m551_-_connect_to_wifi|M550]] ​               | Get/Set SSID                                      + 
-| [[extended_g-code_table#​m550_m551_-_connect_to_wifi|M551]] ​               | Get/Set Password ​                                 +^ Command ​                                                                ​^ Description ​                                         
-| M552                                                                      | Display IP address ​                               +| [[extended_g-code_table#​m550_m551_-_connect_to_wifi|M550]] ​             | Get/Set SSID                                         ​
-| M555 P1                                                                   ​| Reset WiFi interface (Seems to reboot printer   +| [[extended_g-code_table#​m550_m551_-_connect_to_wifi|M551]] ​             | Get/Set Password ​                                    ​
-| M556                                                                      | Display network status ​                           +| M552                                                                    | Display IP address ​                                  ​
-| [[motion_controller#​g-code_-_m560|M560]] ​                                 | Update firmware using update.bin in microSD card  +| M555 P1                                                                 ​| Reset WiFi interface (reboots WiFi module          ​
-| [[extended_g-code_table#​m561_-_change_thermistor_type|M561]] ​             | Change thermistor type (Hotend and/or Heat bed)   ​+| M556                                                                    | Display network status ​                              ​
-| [[extended_g-code_table#​m562_-_invert_stepper_motor_direction|M562]] ​     | Invert stepper motor direction ​                   +| [[firmware:motion_controller#​g-code_-_m560|M560]] ​                      ​| Update firmware using update.bin in microSD card     ​
-| [[extended_g-code_table#​m563_-_enable faster_wifi_file_uploads|M563]] ​    ​| Enable faster WiFi file uploads ​               +| [[extended_g-code_table#​m561_-_change_thermistor_type|M561]] ​           | Change thermistor type (Hotend and/or Heat bed)      
-| [[extended_g-code_table#​m564_-_download_file_from remote_server|M564]] ​                                                ​| Download gcode from remote server ​               +| [[extended_g-code_table#​m562_-_invert_stepper_motor_direction|M562]] ​   | Invert stepper motor direction ​                      ​
-| M565                                                                      | Print cached file cache.gc ​                       +| [[extended_g-code_table#​m563_-_enable faster_wifi_file_uploads|M563]] ​  ​| Enable faster WiFi file uploads<color red>​*</​color>  ​
-| [[extended_g-code_table#​m566_-_rename_cache_file|M566]] ​                  ​| Rename cache.gc ​                                  ​+| [[extended_g-code_table#​m564_-_download_file_from remote_server|M564]] ​ | Download gcode from remote server ​                   
-*//Some of the above commands may not work with firmware versions 22.39 & older. They have been implemented in 26.42 & higher. M561 B - Change ​beat bed thermistor type is included in motion ​firmware ​version 27 & higher.//+| [[extended_g-code_table#​m565_-_print_cache_file_cache.gc|M565]]         | Print cached file cache.gc ​                          ​
 +| [[extended_g-code_table#​m566_-_rename_cache_file|M566]] ​                ​| Rename cache.gc ​                                     | 
 +| M600                                                                    | Pause/​Resume ​                                        
 +*//Some of the above commands may not work with firmware versions 22.39 & older. ​\\ 
 +They have been implemented in 26.42 & higher. ​\\ 
 +[[extended_g-code_table#​561_b_-_heat_bed_thermistor_type|M561 B - Change ​Heat bed thermistor type]] is included in Motion ​firmware ​V27 & higher.//
  
  
Line 30: Line 35:
 ===== M550 & M551 - Connect to WiFi ===== ===== M550 & M551 - Connect to WiFi =====
 <​code>​ <​code>​
-M550 SSID             ​;SSID = Name of WiFi network (case sensitive) +M550 SSID         ​;SSID = Name of WiFi network (case sensitive) 
-M551 PASSWORD ​        ​;PASSWORD = Password for WiFi network (case sensitive)+M551 PASSWORD ​    ​;PASSWORD = Password for WiFi network (case sensitive)
 </​code>​ </​code>​
  
 ---- ----
  
-===== M561 - Change ​thermistor type =====+===== M561 - Change ​Thermistor Type ===== 
 +<wrap lo>​[[parts:​thermistors|Thermistor information and replacement options can be found here.]]</​wrap>​ \\
 //Type **P0** = Default or EPCOS 100K// \\ //Type **P0** = Default or EPCOS 100K// \\
-//Type **P1** = 104GT-2 or 104NT-4-R025H42G (may report as 104GT)//+//Type **P1** = 104GT-2 or 104NT-4-R025H42G (may report as 104GT) // \\ 
 +<wrap lo><​wrap em>​Motion Controller firmware version 26 must be installed to change the hotend thermistor type.</​wrap></​wrap>​ \\ 
 +<wrap lo><​wrap em>​Motion Controller firmware version 27 must be installed to change the bed thermistor type.</​wrap></​wrap>​
  
 +==== M561 - Change Hotend Thermistor Type ====
 +=== Default ===
 +<file gcode change_hotend_thermistor_type_default.gcode>​
 +; G-Code generated by Matthew Upp
 +; Change thermistor type to Default or EPCOS 100K and saves to EEPROM
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +;
 +M561 P0 ; Change to Default or EPCOS 100K
 +M500 ; Save to EEPROM
 +; Reboot the printer to complete the process
 +</​file>​
  
-==== M561 Hotend thermistor type ==== +=== 104GT-=== 
-<code+<file gcode change_hotend_thermistor_type_104gt-2.gcode
-M561 P0             ;Change to Default ​or EPCOS 100K +; G-Code generated by Matthew Upp 
-M500                ;Save EEPROM +; Change ​thermistor type to 104GT-2 ​or 104NT-4-R025H42G (may report as 104GT) and saves to EEPROM 
-Reboot printer ​to complete ​the process +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end. 
-             Or +;              ​ 
-M561 P1             ​;Change to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) +M561 P1 ;Change to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) 
-M500                ;Save EEPROM +M500 ; Save to EEPROM 
-Reboot printer to complete the process +
-</code>+Reboot ​the printer to complete the process 
 +</file>
  
-==== M561 - Heat bed thermistor type ====+==== M561 Change ​Heat Bed Thermistor Type ====
 <​code>​ <​code>​
-M561 B P0           ​;Change to Default or EPCOS 100K +M561 B P0       ​;Change to Default or EPCOS 100K 
-M500                ;Save EEPROM+M500            ;Save EEPROM
 Reboot printer to complete the process Reboot printer to complete the process
              Or              Or
-M561 B P1           ​;Change to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) +M561 B P1       ​;Change to 104GT-2 or 104NT-4-R025H42G (may report as 104GT) 
-M500                ;Save EEPROM+M500            ;Save EEPROM
 Reboot printer to complete the process Reboot printer to complete the process
 </​code>​ </​code>​
  
-<wrap lo><​wrap hi>**Type P0 = Default or EPCOS 100K** \\ +=== Type P0 = Default or EPCOS 100K === 
-//EPCOS 100K Thermistors B57540G0104F000,​ B57560G104F,​ and B57560G1104F have similar Beta values compared to the stocks Beta value of 3950. Because of this you can use B57540G0104F000,​ B57560G104F,​ or B57560G1104F ​as replacement thermistors ​and use the stock thermistor setting of Type P0.//</​wrap>​</​wrap>​+<wrap lo>//EPCOS 100K Thermistors ​''​%%B57540G0104F000%%''​''​%%B57560G104F%%''​, and ''​%%B57560G1104F%%'' ​have similar Beta values compared to the stocks Beta value of 3950. Because of this you can use any of them as replacement thermistors. Use the stock thermistor setting of Type P0.//</​wrap> ​\\
  
-<wrap hi><​wrap lo>**Type P1 = 104GT-2 or 104NT-4-R025H42G** \\ + 
-//Characteristics of 104GT-2 and 104NT-4-R025H42G are nearly identical ​so Type P1 can be used for either thermistor.//</​wrap>​</​wrap>​+ 
 + 
 +=== Type P1 = 104GT-2 or 104NT-4-R025H42G ​=== 
 +<wrap lo>Characteristics of ''​%%104GT-2%%'' ​and ''​%%104NT-4-R025H42G%%'' ​are nearly identical. **Type P1** is used for either thermistor.</​wrap>​
  
 ---- ----
Line 73: Line 96:
 ===== M562 - Invert Stepper Motor Direction ===== ===== M562 - Invert Stepper Motor Direction =====
 <​code>​ <​code>​
-M562 E                ;​Inverts ​extruder ​motor direction +M562 E          ;​Inverts ​Extruder motor direction 
-M500                  ;Saves changes to EEPROM+M562 X          ;Inverts X-Axis motor direction 
 +M562 Y          ;Inverts Y-Axis motor direction 
 +M562 Z          ;Inverts Z-Axis ​motor direction 
 +M500            ;Saves changes to EEPROM
 Reboot printer to complete the process Reboot printer to complete the process
 </​code>​ </​code>​
 +
 +
 +==== M562 X ====
 +<file gcode invert_X-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert X-Axis ​
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S245 ; turn fan on to signify start
 +;
 +;
 +M562 X ; invert X-Axis
 +M500 ; save currently loaded settings to EEPROM
 +;
 +;
 +G28 X ; home X to verify the X-axis is inverted
 +G1 X60 F1000 ; Move X-Axis to center of the bed to signify completion
 +M400 ; Wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +</​file>​
 +
 +
 +==== M562 Y ====
 +<file gcode invert_y-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Y-Axis ​
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S245 ; turn fan on to signify start
 +
 +;  ​
 +M562 Y ; Invert Y-Axis
 +M500 ; Save currently loaded settings to EEPROM
 +
 +;
 +G28 Y ; home Y to verify the Y-axis is inverted
 +G1 Y60 F1000 ; Move Y-Axis to center of the bed to signify completion
 +M400 ; Wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +</​file>​
 +
 +
 +==== M562 Z ====
 +<file gcode invert_z-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Z-Axis
 +; Possibly helpful if you need to invert the Z-axis after switching to a NEMA 17 motor and lead screw
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S245 ; turn fan on to signify start
 +
 +;  ​
 +M562 Z ; Invert Z-Axis
 +M500 ; Save currently loaded settings to EEPROM
 +
 +;
 +G28 Z ; home Z to verify the Z-axis is inverted
 +G1 Z10 F1000 ; Move Z-Axis up 10mm to signify completion
 +M400 ; Wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +</​file>​
  
 ---- ----
  
-===== M563 - Enable ​faster ​WiFi file uploads ​=====+===== M563 - Enable ​Faster ​WiFi File Uploads ​=====
 <​code>​ <​code>​
-M563 S6               ​;S value can be 2-6+M563 S6         ​;S value can be 2-6
 </​code>​ </​code>​
-<wrap lo><​wrap hi>//​This setting doesn'​t persist after the printer has been powered off, i.e., "M563 S6" must be sent at least once after turning the printer on. I gather ​"​M500"​ doesn'​t save changes that are made to settings that are related to the UI Controller firmware.//</​wrap></​wrap>​+ 
 + 
 +**<color red>​*</​color>​****M563 S6 is currently broken with V2 firmware. Try:**  
 + 
 +<​code>​ 
 +M563 S5 
 +</​code>​ 
 + 
 +Or 
 + 
 +<​code>​ 
 +M563 S4 
 +</​code>​ 
 + 
 +==== Web Browser Address Bar ==== 
 + 
 +''​%%http://​PRINTERS_IP_ADDRESS/​set?​code=M563 S6%%''​ \\ 
 +<​code>​ 
 +http://​192.168.20.113/​set?​code=M563 S6 
 +</​code>​ 
 + 
 +Or 
 + 
 +<​code>​ 
 +http://​192.168.20.113/​set?​code=M563 S4 
 +</​code>​ 
 + 
 + 
 +<wrap lo><​wrap hi>//​This setting doesn'​t persist after the printer has been powered off, i.e., "M563 S6" must be sent at least once after turning the printer on. "​M500"​ doesn'​t save changes that are made to settings that are related to the UI Controller firmware.//</​wrap></​wrap>​
  
 ---- ----
  
-===== M564 - Download ​file from remote server ​=====+===== M564 - Download ​File from Remote Server ​===== 
 + 
 +''​%%M564 http://​server/​file.gcode%%''​ \\
 <​code>​ <​code>​
 M564 ip_address_of_file_server/​file.gcode ​   ;Download file.gcode from server M564 ip_address_of_file_server/​file.gcode ​   ;Download file.gcode from server
Line 96: Line 231:
 ---- ----
  
-===== M566 - Rename ​cache file =====+===== M565 - Print Cache File cache.gc ===== 
 +<​code>​ 
 +M565 
 +</​code>​ 
 + 
 +**Or using a web browsers URL bar** \\ 
 + 
 +''​%%http://​PRINTERS_IP_ADDRESS/​set?​code=M565%%''​ \\ 
 +Example: 
 +<​code>​ 
 +http://​192.168.1.120/​set?​code=M565 
 +</​code>​ 
 + 
 +---- 
 + 
 +===== M566 - Rename ​Cache File =====
 <​code>​ <​code>​
-M21                   ​;Initialize SD card  +M21                    ;Initialize SD card  
-M20                   ​;List SD card  +M20                    ;List SD card  
-M566 new_file_name.gc ;renames cache.gc to a user given file name +M566 new_file_name.gc ​ ;renames cache.gc to a user given file name 
-M20                   ​;List SD card (to verify file was renamed)+M20                    ;List SD card (to verify file was renamed)
 </​code>​ </​code>​
  
  
extended_g-code_table.1487755825.txt.gz · Last modified: 2017/02/22 09:30 by Matthew Upp