User Tools

Site Tools


extended_g-code_table

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
extended_g-code_table [2018/06/24 01:13]
Matthew Upp [M561 - Change Hotend Thermistor Type]
extended_g-code_table [2018/12/22 04:16] (current)
Matthew Upp
Line 50: Line 50:
 ==== M561 - Change Hotend Thermistor Type ==== ==== M561 - Change Hotend Thermistor Type ====
 === Default === === Default ===
-<file gcode change_hotend_thermistor_type_104gt-2.gcode>+<file gcode change_hotend_thermistor_type_default.gcode>
 ; G-Code generated by Matthew Upp ; G-Code generated by Matthew Upp
 ; Change thermistor type to Default or EPCOS 100K and saves to EEPROM ; Change thermistor type to Default or EPCOS 100K and saves to EEPROM
Line 103: Line 103:
 Reboot printer to complete the process Reboot printer to complete the process
 </​code>​ </​code>​
 +
 +
 +==== M562 X ====
 +<file gcode invert_X-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert X-Axis ​
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S245 ; turn fan on to signify start
 +;
 +;
 +M562 X ; invert X-Axis
 +M500 ; save currently loaded settings to EEPROM
 +;
 +;
 +G28 X ; home X to verify the X-axis is inverted
 +G1 X60 F1000 ; Move X-Axis to center of the bed to signify completion
 +M400 ; Wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +</​file>​
 +
 +
 +==== M562 Y ====
 +<file gcode invert_y-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Y-Axis ​
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S245 ; turn fan on to signify start
 +
 +;  ​
 +M562 Y ; Invert Y-Axis
 +M500 ; Save currently loaded settings to EEPROM
 +
 +;
 +G28 Y ; home Y to verify the Y-axis is inverted
 +G1 Y60 F1000 ; Move Y-Axis to center of the bed to signify completion
 +M400 ; Wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +</​file>​
 +
 +
 +==== M562 Z ====
 +<file gcode invert_z-axis.gcode>​
 +; G-Code generated by Matthew Upp
 +; Invert Z-Axis
 +; Possibly helpful if you need to invert the Z-axis after switching to a NEMA 17 motor and lead screw
 +; for Malyan M200 & MP Select Mini
 +
 +; Lines with only a semicolon are for making line separations only
 +; Please add a blank line to the end of the file while editing. DokuWiki Code Blocks deletes blank lines at the end of the block but g-code files should end with a single blank line at the end.
 +
 +
 +M107 ; turn fan off in case it was already on
 +M106 S245 ; turn fan on to signify start
 +
 +;  ​
 +M562 Z ; Invert Z-Axis
 +M500 ; Save currently loaded settings to EEPROM
 +
 +;
 +G28 Z ; home Z to verify the Z-axis is inverted
 +G1 Z10 F1000 ; Move Z-Axis up 10mm to signify completion
 +M400 ; Wait for current moves to finish
 +M107 ; turn fan off to signify completion
 +M84 ; disable motors
 +</​file>​
  
 ---- ----
extended_g-code_table.1529802806.txt.gz · Last modified: 2018/06/24 01:13 by Matthew Upp