User Tools

Site Tools


firmware:motion_controller_recovery

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
firmware:motion_controller_recovery [2016/08/22 08:50]
Matthew Upp
firmware:motion_controller_recovery [2019/11/27 17:47] (current)
Matthew Upp old revision restored (2017/07/29 15:54)
Line 1: Line 1:
-===== Recovery ​Mode - Motion Controller =====+====== Recovery ​Method ​- Motion Controller =====
 +----
  
-**Link to firmware:​** ​https://​goo.gl/YTwBs9+<WRAP center round alert 60%> 
 +**This page is not up-to-date. Please see the [[firmware:motion_controller|Motion Controller Firmware]] page.** 
 +</WRAP>
  
-=== The recovery ​mode method can be used as follows: === +---- 
-  - Copy any version "​update.bin"​ firmware file from the firmware folder to the SD card. +---- 
-  - Copy any random file larger than 1MB(megabyte) to the SD card and rename to "​fcupdate.flg"​. ​Or create ​a file named "​fcupdate.flg"​ and copy to the SD card. The file size seems not to matter.+<WRAP center round alert 100%> 
 +**This page is not up-to-date. Please see the [[firmware:​motion_controller|Motion Controller Firmware]] page.** 
 +</​WRAP>​ 
 +---- 
 +---- 
 + 
 +<WRAP center round alert 60%> 
 +**This page is not up-to-date. Please see the [[firmware:​motion_controller|Motion Controller Firmware]] page.** 
 +</​WRAP>​ 
 + 
 +<WRAP center round alert 100%> 
 +<WRAP group> 
 +<WRAP column half> 
 +<wrap lo><​wrap em>If you received a Select Mini V1 or V2, black or white and the UI looks like the photo, do <wrap hi>​__NOT__</​wrap>​ update the firmware with any currently available firmware version. Some V1's & V2's, white or black do <wrap hi>​__NOT__</​wrap>​ use the same firmware as previous V1 & V2's. \\ 
 +\\ 
 +If your Select Mini has Motion Controller version 31+ or higher pre-installed,​ do <wrap hi>​__NOT__</​wrap>​ use V1 Motion Controller firmware. There is not any firmware updates yet available for the Select Mini V2. \\ 
 +\\ 
 +If your Select Mini has UI Controller version 106.2 or similar pre-installed,​ do <wrap hi>​__NOT__</​wrap>​ use V1 UI Controller firmware which is any versions 33 through 42. \\ 
 +\\ 
 +I know all that is a bit confusing and may not make sense to anyone other than myself. Basically if you have a Select Mini V2 or V1 that has the UI seen in the picture, don't update the firmware. \\ 
 +</​wrap></​wrap>​ 
 + 
 +</​WRAP>​ 
 + 
 +<WRAP column half> 
 + 
 +{{gallery>​ :​wiki:​mpsm_new_ui_example_collage_20170623.jpg?&​270x270&​1&​lightbox }} 
 + 
 + 
 +</​WRAP>​ 
 +</​WRAP>​ 
 +</​WRAP>​ 
 + 
 + 
 + 
 +<WRAP center round info 100%> 
 +<wrap lo> 
 +Do you have a black screen after falling victim to updating the firmware after watching a video or maybe you outright ignored the warnings? You can contact me in one of the following online community groups so that we may schedule a time to get your printers display back to the way Monoprice intended it to be. \\ 
 +[[https://​facebook.com/​groups/​1717306548519045/​|MP Select Mini Owners Facebook Group]] - Name: [[https://​www.facebook.com/​matthewupp|Matthew Upp]] \\ 
 +[[https://​reddit.com/​r/​MPSelectMiniOwners/​|MPSelectMiniOwners subreddit]] - User: [[https://​www.reddit.com/​user/​tiny_tim_|tiny_tim_]] \\ 
 +[[https://​plus.google.com/​communities/​116802523766279866092|Monoprice MP Select Mini Google+ Community]] - Name: [[http://​google.com/​+MatthewUpp|Matthew Upp]]\\ 
 +//(This is only a temporary fix. When the V1's have definitely stopped shipping and fully tested firmware for the V2 is released, this process will not need to be done.)//</​wrap>​ 
 + 
 +</​WRAP>​ 
 + 
 + 
 +<wrap em>​**UPDATING THE FIRMWARE IS NOT SUPPORTED BY MONOPRICE** </​wrap>​\\ 
 +<wrap lo><​wrap em>Do not update the firmware before completing a few prints. \\ 
 + 
 +Updating the firmware before using the printer introduces another variable to the troubleshooting session you may have to go through.</​wrap></​wrap>​ \\ 
 + 
 +**[[downloads:​start|Link to V1 firmware]]** 
 + 
 +<wrap hi>//​Note:​ If you have trouble updating, please format microSD card or use another microSD card and try again. Try a microSD card that is 4GB or less formatted with FAT. The printer can be picky at which cards it will update from so try a few cards.//</​wrap>​ 
 + 
 + 
 + 
 +=== The recovery method can be used as follows: === 
 +  - Copy any version ​of "​update.bin" ​Motion Controller ​firmware file to the root of the microSD ​card. 
 +  - Copy the file named "​fcupdate.flg" ​file to the root of the microSD cardIf this file is missing it can be derived a few different ways listed below. 
 +      * Creating ​a file and name it "​fcupdate.flg"​ 
 +      * Copying an existing file from your computer ​and rename it to "​fcupdate.flg"​ 
 +      * Downloading from [[http://​fw.mpselectmini.com|MP Select Mini Share - Google Drive]] ​ //​Firmware//​ >> //​Individual//​ >> //Motion// >> //​**fcupdate.flg**//​ 
 +  - Put the microSD ​card in the printers microSD card slot/reader.
   - Power on the printer. When the printer is powered on, it will force the update.   - Power on the printer. When the printer is powered on, it will force the update.
-  - **IMPORTANT:​** After successfully updating, remove ​the SD Card and delete the "​fcupdate.flg"​ file. You may also delete the "​update.bin"​.+  - **IMPORTANT:​** ​ After successfully updating, remove ​microSD ​Card and delete the "​fcupdate.flg"​ file. You may also delete the "​update.bin" ​file. \\ <wrap hi>//(If flashing to a different version then follow the steps below)//</​wrap>​ 
 +  - Export/Save any calibration you have done as the next step will erase/reset everything back to defaults. 
 +  - Reset EEPROM using “M502” and save EEPROM using “M500” \\ Need help on how to send these commands? See [[:​g-code#​sending_g-code|Sending G-code]] 
 +  - (Optional) Run [[:​pid_autotune|PID Autotune]] 
 + 
 + 
 +<WRAP center round important 100%> 
 + 
 +==== Trouble recovering? ==== 
 +  * Format microSD card or use another microSD card and try again. 
 +  * Try a microSD card that is 4GB or less formatted with FAT 
 +  * Verify the x-axis endstop is not pressed in. 
 +</​WRAP>​ 
 + 
 + 
 +---- 
 + 
 + 
 +<WRAP center round alert 60%> 
 +**This page is not up-to-date. Please see the [[firmware:​motion_controller|Motion Controller Firmware]] page.** 
 +</​WRAP>​
firmware/motion_controller_recovery.1471855849.txt.gz · Last modified: 2016/08/22 08:50 by Matthew Upp