User Tools

Site Tools


parts:thermistors

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
parts:thermistors [2016/08/03 06:02]
127.0.0.1 external edit
parts:thermistors [2020/02/22 02:20] (current)
Matthew Upp
Line 1: Line 1:
-==== Thermistor for M200 (Select Mini) ==== +~~NOTOC~~ 
-"Extruder and hotbed are all 100K NTC resistor with beta 3950"+====== Thermistors ====== 
 +----
  
-Source: +The hotend and heat bed thermistor are both 100K NTC resistor with beta 3950. \\ 
-http://wiki.malyansys.com/doku.php?id=type_of_thermistors_of_m200+The stock hotend thermistor uses a glass bead thermistor\\ 
 +The stock heat bed uses a SMD thermistor but can be [[howto:thermistor_heatbed|easily replaced]] with a glass bead type\\
  
 +A few [[thermistors#direct_replacement|stock replacement options]] listed below.
  
-==== Replacements ==== 
  
 +-----
  
-** RioRand(TM) Upgraded 10 pcs 100Kohm NTC Thermistors thermistor,temperture sensor,Reprap,Prusa 3D printer ** \\ +<wrap em><wrap lo>As of motion controller firmware version 26 the MP Select Mini is no longer limited to only using a 3950 thermistor for the hotend. \\ 
-Link: https://amzn.com/B00GD471PO \\ +Version 27 added this ability to the heat bed.</wrap></wrap> \\
-NOTE: Leads are not insultaed. You must insulate the leads before using.+
  
-** Anycubic NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Bed or Hot End Pack of 5PCS ** \\ +Using the custom G-code command [[:extended_g-code_table#m561_-_change_thermistor_type|M561]] the thermistor type can be changed for the hotend and heat bed. \\ The hotend and heat bed can each use a different type of thermistors.\\
-Link: https://amzn.com/B01B41K7OM \\ +
-NOTE: The JST plug can be cut off. You may also choose to cut the wire closer to the thermistor to use the existing wiring.+
  
-** 2pcs M3 Screw on Modular Design NTC 3950 100k Thermistor with 1m Cable Wire ** \\ +---- 
-Linkhttps://amzn.com/B01BA8BNB0 \\ + 
-NOTE: The M3 stud screws into the heater block.+===== M561 - Change thermistor type =====  
 +See the [[:extended_g-code_table|Extended G-code Table]] page for instructions on how to use custom G-code command [[:extended_g-code_table#m561_-_change_thermistor_type|M561 - Change thermistor type (Hotend and/or Heat bed)]] 
 + 
 + 
 + 
 +==== Type P0 = Default or EPCOS 100K ==== 
 +<wrap lo>//EPCOS 100K Thermistors ''%%B57540G0104F000%%'', ''%%B57560G104F%%'', and ''%%B57560G1104F%%'' have similar Beta values compared to the stocks Beta value of 3950. Because of this you can use any of them as replacement thermistors. Use the stock thermistor setting of Type P0.//</wrap> \\ 
 +\\ 
 + 
 +==== Type P1 = 104GT-2 or 104NT-4-R025H42G ====  
 +<wrap lo>Characteristics of ''%%104GT-2%%'' and ''%%104NT-4-R025H42G%%'' are nearly identical. **Type P1** is used for either thermistor.</wrap> 
 + 
 +----- 
 + 
 +===== Direct Replacement ===== 
 +**GiGDigit** - **[[https://gigdigit.com/thermistor-mp-select-mini-v1-v2/|Thermistor - MP Select Mini V1/V2]]** 
 + 
 + 
 +---- 
 + 
 +===== Aftermarket Replacements ===== 
 + 
 +**Amazon.com** - [[http://amzn.to/2D7wqk5|RioRand(TM) Upgraded 10 pcs 100Kohm NTC Thermistors]] \\ 
 +:!: <wrap em><wrap lo>Leads are not insulated. You must insulate the leads before using</wrap></wrap> \\ 
 + 
 + 
 +**Amazon.com** - [[http://amzn.to/2BX1ALx|Anycubic NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Heatbed or Hot End Pack of 5PCS]] \\ 
 +<wrap em><wrap lo>**NOTE:** The JST connector can be cut off. You may also choose to cut the wire closer to the thermistor to use the existing wiring.</wrap></wrap> 
 + 
 + 
 +**Amazon.com** - [[http://amzn.to/2C2UzeH|[3D CAM] 3 PCS NTC3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed pre-wired with Teflon Insulated Wiring]] \\ 
 +<wrap em><wrap lo>**NOTE:** Wired - No female pin connector</wrap></wrap> 
 + 
 + 
 +**Amazon.com** - [[http://amzn.to/2D7gkHj|Mmei 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Extruder Heated Bed pre-wired or Hot End]] \\ 
 +<wrap em><wrap lo>**NOTE:** Wired - With female 2 pin connector (connector may not be the correct size but can be cut off)</wrap></wrap> 
 + 
 + 
 +**Amazon.com** - [[http://amzn.to/2DtRzZy|Happisland 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer]] \\ 
 +<wrap em><wrap lo>**NOTE:** Wired - With female 2 pin connector (connector may not be the correct size but can be cut off)</wrap></wrap> 
 + 
 + 
 +/* 
 +**Amazon.com** - [[http://amzn.to/2BI4abp|Mercurry NTC 3950 100K Thermistor with 1 Meter Wiring for RepRap 3D Printer Bed or Hot End Pack (10PCS)]] \\ 
 +<wrap em><wrap lo>**NOTE:** Wired - No female pin connector</wrap></wrap> 
 +*/ 
 + 
 +**Amazon.com** - [[http://amzn.to/2BWQNkB|2pcs M3 Screw on Modular Design NTC 3950 100k Thermistor with 1m Cable Wire]] \\ 
 +<wrap em><wrap lo>**NOTE:** The M3 stud screws into the heater block.</wrap></wrap> 
 + 
 + 
 +---- 
 + 
 +/* 
 + 
 +===== 104GT-2 Replacements Options ===== 
 + 
 +**Amazon.com** - [[http://amzn.to/2BIhsoC/|Gikfun 100K ohm NTC B4267 ATC Semitic 104GT-2 Thermistor for 3D Printer Reprap (Pack of 10pcs) EK9018]] \\ 
 +:!: <wrap em><wrap lo>Leads are not insulated. You must insulate the leads before using</wrap></wrap> \\ 
 +<wrap em><wrap lo>**NOTE:** Requires updating the firmware's thermistor value. This is done by sending the custom G-code command "M561 P1" & then "M500". \\ 
 +**NOTE:**  [[:extended_g-code_table#m561_-_change_thermistor_type|M561 - Change thermistor type]] & [[parts:thermistors|Thermistors]]</wrap></wrap> \\ 
 + 
 + 
 +(These are only a few that will work. This is not an exhaustive list.) 
 + 
 +*/
  
-(These are only a couple that will work. This is not an exhaustive list.) 
parts/thermistors.1470204152.txt.gz · Last modified: 2016/09/12 19:30 (external edit)