User Tools

Site Tools


User's Manual & Quick Start Guide


Where to Purchase

Donations & Support

Replacements Parts & Information

Mods & Improvements



Slicer Stuff




Web UI



Donations & Support

Amazon Affiliate Program Disclosure

Looking for the Malyan M300 Mini Delta 3D Printer Site?


This is an old revision of the document!

Thermistor for M200 (Select Mini)

Original hotend and heat bed are both 100K NTC resistor with beta 3950.
The stock hotend thermistor uses a glass bead thermistor.
The stock heat bed uses a SMD thermistor but can be easily replaced with a glass bead type. \\

A few stock replacement options listed below.

As of motion controller firmware version 26 the MP Select Mini is no longer limited to only using 100K NTC thermistor with Beta 3950 for the hotend. Version 27 added this ability to the heat bed.
With custom G-code command “M561” the thermistor type can be changed for the hotend and heat bed.
The hotend and heat bed can use different type of thermistors for each.

M561 - Change thermistor type

See the Extended G-code Table page for instructions on how to use custom G-code command "M561".

Type P0 = Default or EPCOS 100K
EPCOS 100K thermistors B57540G0104F000, B57560G104F, and B57560G1104F have similar Beta values compared to the stocks Beta value of 3950. Because of this you can use B57540G0104F000, B57560G104F, or B57560G1104F as replacement thermistors. Type P0 is used for the stock thermistor and the previously mentioned EPCOS 100K thermistors.

Type P1 = 104GT-2 or 104NT-4-R025H42G
Characteristics of 104GT-2 and 104NT-4-R025H42G are nearly identical. Type P1 is used for either thermistor.

Stock Replacements Options

RioRand(TM) Upgraded 10 pcs 100Kohm NTC Thermistors
NOTE: Leads are not insulated. You must insulate the leads before using.

Anycubic NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Bed or Hot End Pack of 5PCS
NOTE: The JST connector can be cut off. You may also choose to cut the wire closer to the thermistor to use the existing wiring.

[3D CAM] 3 PCS NTC3950 Thermistors for RepRap 3D Printer Extruder or Heated Bed pre-wired with Teflon Insulated Wiring
NOTE: Wired - No female pin connector

Mmei 5pcs NTC 3950 100K Thermistor with 1 Meter Wiring and Female Pin Head for RepRap 3D Printer Extruder Heated Bed pre-wired or Hot End
NOTE: Wired - With female 2 pin connector (connector may not be the correct size but can be cut off)

Mercurry NTC 3950 100K Thermistor with 1 Meter Wiring for RepRap 3D Printer Bed or Hot End Pack (10PCS)
NOTE: Wired - No female pin connector

2pcs M3 Screw on Modular Design NTC 3950 100k Thermistor with 1m Cable Wire
NOTE: The M3 stud screws into the heater block.

104GT-2 Replacements Options

Gikfun 100K ohm NTC B4267 ATC Semitic 104GT-2 Thermistor for 3D Printer Reprap (Pack of 10pcs) EK9018 These thermistors will require using sending command “M561 B P1” and “M500”. Go here to more info M561 - Change thermistor type.

(These are only a few that will work. This is not an exhaustive list.)

parts/thermistors.1485654327.txt.gz · Last modified: 2017/01/29 01:45 by Matthew Upp