Malyan M200 3D Printer

User Tools

Site Tools

You are here: Malyan M200 3D Printer » Replacement Parts
replacements_parts

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
replacements_parts [2016/12/05 20:35]
Matthew Upp 		replacements_parts [2019/10/04 06:21]
Matthew Upp
Line 1: Line 1:
 ===== Replacement Parts ===== ===== Replacement Parts =====
 +<WRAP group>
 +<WRAP half column>
 +
 +    * [[parts:bearings|Bearings]]
 +    * [[parts:belts|Belts]]
 +    * [[parts:ptfe_tubes|Bowden Tube]]
 +    * [[parts:bowden_tube_connectors|Bowden Tube Connectors]]
 +    * [[parts:cup_washers_and_spring|Cup Washers & Spring]]
 +    * [[parts:lcd_screen|Display]]
 +    * [[parts:endstops|Endstops]]
 +    * [[parts:extruder|Extruder / Feed Mechanism]]
 +    * [[parts:fan_hotend|Fan for Hotend]]
 +    * [[parts:fan_mainboard|Fan for Mainboard - V2]]
 +    * [[parts:heater_block|Heater Block]]
 +    * [[parts:heater_block_insulation|Heater Block Insulation & Tape]]
 +    * [[parts:heat_bed|Heat Bed]]
 +    * [[parts:heat_bed_rewire_kit|Heat Bed Rewire Kit]]
 +    * [[parts:screws_heat_bed|Heat Bed Leveling Screws]]
 +    * [[parts:heat_break|Heat Break / Throat]]
 +    * [[parts:heatsink|Heatsink - V1 & V2]]
 +    * [[parts:hotend|Hotends]]
 +    * [[parts:lcd_screen|LCD Screen]]
 +    * [[parts:mainboard|Mainboard / Motion Controller]]
 +    * [[parts:microsd_card|microSD Card]]
 +    * [[parts:nozzle|Nozzle]]
 +    * [[parts:power_supply|Power Supply]]
 +    * [[parts:power_switch|Power Switch]]
 +    * [[parts:ptfe_tubes|PTFE Tubes]]
 +    * [[parts:pulleys|Pulleys]]
 +    * [[parts:rotary_encoder|Rotary Encoder / Control Dial]]
 +    * [[parts:screws_heat_sink|Set Screw & Square Nut - Heat Break and Bowden Connector]]
 +    * [[parts:screws_heat_bed|Screws - Heat Bed]]
 +    * [[parts:stepper_motors|Stepper Motors]]
 +    * [[parts:thermistors|Thermistors]]
 +    * [[parts:heat_break|Throat / Heat Break]]
 +    * [[parts:torsion_springs|Torsion Springs for Hotend Fan Shroud]]
 +    * [[parts:ui_controller_board|UI Controller Board]]
 +    * [[parts:wire_connectors|Wire Connectors]]
 +    * [[parts:heat_bed_rewire_kit|Wire Kit for Heat Bed]]
 +    * [[thingiverse:x-axis-endcap|X-Axis Endcap]]
 +    * [[parts:z-axis_threaded_rod|Z-Axis Threaded Rod]]
 +
 +----
 +
 +</WRAP>
 +
 +<WRAP half column>
 +
 +For direct replacement parts and some not listed above or to the left, check out **[[https://gigdigit.com|GigDigit.com]]** \\
 +[[https://gigdigit.com|{{:wiki:logo_-_dot_com_-_2050_x_650.png?nolink&250}}]]
 +
 +</WRAP>
 +</WRAP>
  
-  * [[Extruder|Extruder]] 
-  * [[belts|Belts]] 
-  * [[lcd_screen|LCD Screen]] 
-  * [[Linear Bearings|Linear Bearings]] 
-  * [[main_board|Main Board]] 
-  * [[Nozzle|Nozzle]] 
-  * [[Power Supply|Power Supply]] 
-  * [[screws_heat_bed|Screws - Heat Bed]] 
-  * [[Stepper Motors|Stepper Motors]] 
-  * [[Thermistors|Thermistors]] 
-  * [[ui_controller_board|UI Controller Board]] 
  
  
replacements_parts.txt · Last modified: 2021/09/10 09:14 by Matthew Upp

Page Tools

Except where otherwise noted, content on this site is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki